Get the most out of your vehicle today with Unitronic Performance ECU software for your Audi A3, Golf, Golf Sportwagen and Alltrack equipped with the 1.8T Gen 3 TSI engine and an upgraded IS20 turbocharger
Stage 2 IS20 - 301 HP / 310 LB-FT (+131 HP / +125 LB-FT)
- Requires an aftermarket 3" downpipe
- Requires an IS20 turbocharger
- Requires 93 Octane Fuel
- Requires an aftermarket high flow intake
- Requires an upgraded intercooler
Features
-
Engineered with Strict Industry Standards:
With over 10 years of experience in Bosch and Siemens engine management calibration, Unitronic is able to utilized its industry leading tools and equipment to assure an optimal calibration; delivering maximum performance, while maintaining complete OEM-like reliability and drivability. -
Extensively Tested Under Various Driving Conditions:
Development begins using its in-house engine dyno housed in an environmentally controlled cell; closely monitoring a plethora of operational data, utilizing industry leading calibration tools and resources. Additional validation and results comparison are completed using its in-house Maha Chassis dyno as a second step of product development. Beta calibrations are then tested in race and street scenarios, using multiple cars throughout the world under various driving conditions. This engine calibration strategy ensures Unitronic Performance Software delivers maximum performance, OEM-like drivability and reliability anywhere in the world. Unitronic Performance Software is only released to its Clients once development is thoroughly completed in accordance to Unitronic’s strict standards. -
Factory Safety Limiters Retained:
OEM “fail safes” are retained within the ECU calibration. Close monitoring of all operation parameters ensures that engine operation stays within factory components limits, resulting in an OEM-like drivability and reliability. -
Engine Temperature Protection (Rev Limit based on Engine Coolant Temperature):
Engine speed limit protection active under warm-up to prevent potential damage when coolant temperature is not within operation range. -
Optimized Responsiveness and Drivability:
Professionally calibrated to improve engine response and reduce drive-by-wire lag. Optimized torque curve for more low end torque and faster turbo spool. -
Optimized Smoothness and Driving Comfort:
Due to the large flat torque curve, the calibration offers a smooth operation under normal and hard acceleration. This results in linear acceleration with constant torque without low end torque peak that will cause loss of traction and uncontrollable power surge, at the expense of high engine speed power. -
Optimized Maximum Output:
Unitronic development team delivers the maximum power output while staying within the operational limits of the factory components used. Specifically, this results in the highest engine performance without sacrificing the reliability of the engine, turbocharger, or other engine components. - Power Delivery Perfectly Optimized Throughout the Power Band:
Aligned with the OEM strategy, the calibration is designed to offer a large flat torque plateau to provide a smooth and linear power band. Maximum torque output is achieved sooner and maintained longer which creates a broader torque plateau and greater area under the curve. This results in an improved acceleration and optimal engine operation. -
Improved Fuel Efficiency:
Optimized timing and injection under cruising condition for an improved fuel efficiency. -
Speed Governor Removed:
Vehicle speed limiter within ECU is removed. (If automatic, subject to transmission rotational speed limit) -
Ignition Timing Precisely Calibrated for Higher Octane Fuel:
Engine calibration optimized to take advantage of higher fuel quality to extract maximum energy from the combustion. Therefore, when using a higher octane fuel, more power and better fuel efficiency will be achieved. -
OEM IS20 Turbo Upgrade Calibration:
With maximum turbocharger efficiency reached with Stage 1, Stage 1+ and Stage 2, Unitronic developed a unique solution to bridge the gap between Stage 2 and Stage 2+ (IS38) turbo upgrade. This results in the use of a factory IHI IS20 turbocharger, from a MK7 GTI, as a complete bolt-on solution producing a power increase of 44hp and 19lb-ft tq over the Stage 2 output, using the OEM turbocharger (IS12). -
Full Staged Software Suite
Includes all Stage 2 tune variants and all lower software stages as well.
Fitment/Applications
- 2015-2019 VW Mk7, Mk7.5 Golf, Sportwagen, Alltrack 1.8T
- 2015-2016 Audi A3 1.8T
Installation
UniConnect+ Software Interface
UniCONNECT+ gives you the freedom to effortlessly install your Unitronic Performance ECU and DSG Software from the comfort of your own home or garage.*
Unitronic (and NGP) recommends the use of battery chargers to ensure, uninterrupted, trouble-free, flashing at home! If you do not use a good battery charger while programming your ECU, you run the risk of damaging it should your battery voltage drop below recommended levels.
Includes Unitronic carrying case.
Change Software Maps
Quickly and Easily re-flash your ECU with Performance Software maps designed and specifically calibrated to suite the hardware and fuel modifications or fuel grade used.
Data Logging
Gathering high resolution data is made easy with Unitronic’s pre-configured channel loadouts for fast and effortless troubleshooting and data logging.**
Simple back to factory restoration
UniCONNECT+ makes it painless to revert your ECU back to it’s stock calibration within minutes.*
Advanced Settings
Enable optional advanced settings such as Launch Control or No Lift Shifting within minutes. Enable Gear display in MFG for DSG Software owners.*
Technical Specifications
Minimum System Requirements:
- Operating System: Microsoft Windows 10
- Internet Explorer 11
- Screen Resolution: 1024x768
- Processor: 1.5 GHz or higher
- Memory (RAM): 4GB or more
For optimal application performance:
- Operating System: Microsoft Windows 10 or higher
- Internet Explorer 11 or newer
- Screen Resolution: 1024x768
- Processor: 2.0 GHz or higher
- Memory (RAM): 8GB or more
Internet access is required.
Do you prefer professional installation?
If you are local to one of our shops and would prefer to have us install this software, please contact one of our shops to set up an appointment.
Please note that this software may not be available for all ECU IDs. DSG software is for Audi A3, AWD Sportwagen and Alltrack only.
The Unitronic+ Programmer is not returnable under most circumstances. The only exception for this policy is if you were to receive your cable and Unitronic does not have a tune for your vehicle.