Sale

Questions? We've got answers.

Dinan + Performance Engine Software - BMW B58 (M0) Engine

Dinan
D900-B58-F-S1-W
Shop Install Only
F22/F23/F30/F32/F33/F36 G01/G02/G11/G12/G30/G32
$1,099.95 $989.96
$989.96

Dinan + Performance Engine Software - BMW B58 (M0) Engine
An eternity in the making-- Dinan flash tuning is now available for a wide variety of BMW B58 powered platforms (B58B30M0 specifically). With over 3 years of development spanning engine control modules (piggybacks) and engine calibrations (flash software) specifically for the B58 engine, every switch/bit has been flipped in the quest for maximum power. Not just any power however - safe, reliable power that does not sacrifice the long-term health of the engine. Dinan performance engine software is so much more than just turning up the turbo boost after all. It is a fully re-tuned engine management program that maximizes power while keeping all the BMW factory safeguards in place. In most cases Dinan software engineers also implement their own additional safety precautions in order to guarantee flawless performance that may not have been needed with factory power levels/programming. Protecting your BMW, while giving the most performance, is the definition of "Performance Without Sacrifice". To do just that, drivetrain and engine components are analyzed for strength, and then the calibration is tested on the dyno and in the real world for durability and drivability. This process has been a cornerstone of Dinan software development for decades and a major reason why Dinan performance tunes are often labelled as being the smoothest, factory-like solution in the marketplace. Unlike historical Dinan flashes that were limited to a warranted 91/93 octane mapping, the new breed of engine calibrations are offered in numerous configurations depending on your specific needs, desires or limitations. Whether you are limited to 91 pump gas, want to experience maximum performance on 104 octane race gas at the track, or something in between, chances are Dinan has an option for you. At its core Dinan offers 2 base options; Stage 1 and Dinan +. The Dinan Stage 1 Performance Engine Software is designed for the B58 engine to yield maximum power (for a variety of different octanes), improve drivability, and remove the factory speed governor for unadulterated entertainment. The Dinan + variant of software offers these same features (albeit limited to 91/93 octane) but also carries the signature Dinan 4yr / 50k, factory matching new car warranty that the brand is synonymous with.

Features:

  • More Power: Max gains up to 50 WHP / 67 lb-ft of torque over stock on 91 octane. Consult the performance charts for detailed data.
  • Dinan + performance software matches the factory new car warranty (4year / 50,000 mi) and is the warranty protection commonly associated with the Dinan brand.
  • No required parts. Install on a stock car and receive the full power gains.
  • Full map rescaling for drivability from idle to wide open throttle and everywhere in between.
  • Optimized boost control, cam phasing, fueling, airflow and temperature controls for maximum power output that is also safe and reliable.
  • Top speed governor (VMAX) removed.
  • Upgradeable from DINANTRONICS Elite (V1 or V2) via trade-in program. See the FAQ linked below for details.
  • Retains all BMW factory engine safeguards and adds additional safety precautions.
  • Torque gains drastically improve acceleration.
  • Sport gauges rescaled to reflect higher than stock power output.

2021+ MY is currently not supported. See DME unlock and compatibility notices at the bottom of the product page for information on potential installation/compatibility limitations.

Emissions

This part is legal under the provisions of EPA’s Tampering Policy dated November 23rd, 2020. The company has reasonable basis (test results) to verify that this product allows the vehicle to operate within legal emissions standards and is therefore legal to be sold for on-street use in all states that accept the legal provisions of the Clean Air Act and the EPA Tampering Policy. This product is NOT LEGAL FOR SALE OR USE IN THE STATE OF CALIFORNIA. Testing with the California Air Resources Board, in order to achieve 50-state compliance, is pending with CARB. Once testing is complete with California, and an E.O. number is issued, this product will be updated to 50-state legal status.

Calibration Quick Reference

All info supplied in the table below is 'at the crank' for consistency when comparing data with BMW advertised numbers which are always reported at the crank. 

Table also represents all possible ECU software options currently available for the selected platform. Some stages / variants may require additional hard parts to achieve advertised numbers.

STAGE / WARRANTY / PRICE HP (CRANK) TQ (CRANK) MAX GAIN MAX GAIN
Stock as Reported by BMW 320 HP 332 LB-FT
Stock as Measured by Dinan 353 HP 347 LB-FT
DINAN + / 4YR/50K / $1,099.95
Dinan + (91 Octane) 410 HP 407 LB-FT +57 HP +70 LB-FT
STAGE 1 / LIMITED / $499.95
91 Octane 410 HP 407 LB-FT +57 HP +70 LB-FT
93 Octane 428 HP 423 LB-FT +75 HP +85 LB-FT
100 Octane 464 HP 469 LB-FT +111 HP +129 LB-FT
Only use fuel equal to or higher than specified. Never use a lower octane fuel. Always follow our fuel guide, especially with race fuel and Ethanol, where available. Dynos are for reference only. Results will vary. Contributing factors include the vehicle condition, vehicle setup, dyno type, dyno setup, environmental factors, fuel quality, and more.

DME UNLOCK & FLASH NOTICE / HOW TO PURCHASE

B58 DME's must be unlocked and bench flashed by Dinan. While dealer / retail unlock and flashing tools are in development and will be available in the future, at present, we must remove your ECU and send it to Dinan. Please contact us for more details.

At no time during the unlocking process is the DME opened or physically modified. If the DME is flashed back to stock, it will need to be unlocked again. Also, vehicle manufacturers issue many DME part numbers and revisions throughout their vehicle lineup. As such, some DMEs may be temporarily unavailable as new parts and/or revisions are released.

CODE CLEARING: Customers doing the DME removal/install process themselves should be aware that in the case a fault code occurs, having the ability to read and erase fault codes is crucial. Failure to be able to perform this task may result in a vehicle that is inoperable. Dinan will not cover any expenses related to not being able to clear codes (towing, equipment rental, etc.).

COMPATABILITY NOTICE

BOX CODES: The B58 engine and its multitude of variants account for numerous unique box codes across various platforms. While Dinan has created files for many of these permutations, there is a chance you may have a box code that we have not seen. If this happens to be the case we will need to create a file for your vehicle. This process could add up to 7 days to the bench flash process although in most cases it will be turned around within 2 business days.

ENGINE VARIANTS: D900-B58-F-S1 (-W) performance engine software is specifically tuned to function with the B58B30M0 engine variant. The B58B30M1 and B58B30O1 engine variants found in the G chassis X5/X7/8 Series and G20 M340i among other applications are not currently supported by this release. B58B30M1 may be supported at a future date by this specific software following additional validation.

Read More
Read Less

Customer Reviews

Be the first to write a review
0%
(0)
0%
(0)
0%
(0)
0%
(0)
0%
(0)

Your cart

×